Introducing the ultimate fuel upgrade for your 03-07 6.0L engine that is equipped with an Odawg Stage 2 intake plenum. The CNC Fabrication 4-Line feed stainless steel fuel line kit! Designed with precision and durability in mind, this kit will take your fuel system...

Are you experiencing a rough running 7.3L or 6.0L Powerstroke or wondering what size of injectors you really have? Send us your set of Powerstroke injectors to CNC Fabrication for testing service on your set of 8 injectors that will let you know the...

98.5-03 7.3L CNC Fabrication, LLC 4R100 Transmission Cooler Line Kit This kit is to replace your factory 4R100 transmission cooler lines with 3/8" hose barbs to match the factory transmission cooler ports.  NOTE: If you need transmission hose, we recommend the Gates 27059 as...

TRUCK YEARS: 1994.5-03 ENGINE TYPE: 7.3L This kit will work great for any horsepower level from stock to well over 1000HP trucks.  It will clear any T4 and T4i turbo mount setup that is currently available and works very well with stacked twin HPOP setup...

Upgrade your 1994.5-1997 7.3L Ford Powerstroke with a set of CNC Fabrication, LLC intake plenum boots.  Features: 5-layer aramid reinforced silicone for high temp rating Rated to 180psi Stainless Steel American made T-bolt clamps (not cheap worm gear hose clamps) Direct replacement of factory...

These CNC Fabrication, LLC billet intake plenums are a nice upgrade over the stock flimsy stamped sheet metal and will not deform the center inlet port when installing your CAC boot clamps. Features: High strength 6061-T6511 aircraft aluminum Bolt/nut kit included Tube of Permatex...

Replace your rusted 94.5-97 E4OD 7.3L Ford Powerstroke transmissions lines with an upgraded CNC Fabrication stainless steel line kit.  This kit is to replace your factory E4OD transmission cooler lines with 5/16" hose barbs to match the factory transmission cooler ports.  NOTE: If you...

This line is a replacement driver side line for the 94.5 through '03. Fittings are the same style as those used on the 94.5-97 powerstroke engines. All new Genuine Brennan™ fittings  DuPont Teflon™ lining just like OEM Burst pressure rating of 16,000psi Working temperature...

This is a replacement line for 98.5-03 Superduty passenger or driver side, or 94.5-97 OBS driver side.  Fittings are the same style as those used on the 94.5-97 Powerstroke engines. This line can be used on 94.5-97 trucks that have e-fuel for a cleaner...

MUST ALREADY HAVE ONE OF THE 4 LINE FEED FUEL BOWL RETAIN KITS TO USE THIS PART. YOU ALSO NEED TO HAVE A FILTER AND REGULATOR FOR THIS TO WORK PROPERLY.  IF YOU DO NOT HAVE A FILTER KIT, PLEASE CHOOSE OURS FROM THE...

98.5-03 7.3L Replacement Fitting Pack for CNC Fabrication HPO 2 Line Kit - 424024 All new Brennan™ Hydraulic fittings  High quality Viton™ o-rings  ***Free shipping is USPS First Class when ordered alone*** DOWNLOADABLE INSTALL INSTRUCTIONS INSTALLATION: Disconnect the battery grounds before installation to avoid...

Installing these 94.5 - Early 99 bushings will help keep you from crushing/distorting the factory stamped sheet metal intake plenums when tightening down your CAC boots.  Includes 2 bushings, one for the passenger side and one for the driver side plenums.  Shipping: ***Free shipping is...

Upgrade your 1994.5-2003 7.3L Ford Powerstroke with this extreme duty billet steel SFI rated E4OD or 4R100 flexplate from CNC Fabrication, LLC.  Features: Thicker material than our stamped SFI flexplate Black Oxide finish to resist corrosion Fully balanced SFI rated FLEXPLATE INSTALL INSTRUCTIONS

Here's the solution you were looking for to re-seal your 7.3L HPOP and line fittings. This will re-seal all 6 fittings on our 3 line HPOP Line kits along with the rear construction port and passenger side construction port on the pump. This kit...

This manifold block is for those who have already installed the Ford JOB2 5R110W transmission pan and filter found in the 2008.5-2010 6.4L Powerstroke.  If you have not installed the later 6.4L Powerstroke transmission pan and filter, then please add the part number 6.0-TFBM-KIT...

98.5-03 7.3L CNC Fabrication, LLC ZF6 Transmission Cooler Line Kit This kit is to replace your factory ZF6 transmission cooler lines with 3/8" hose barbs to match the factory transmission cooler ports.  NOTE: Please be mindful that these lines are one piece and rather...

98.5-03 7.3L CNC Fab 4R100 Transmission Cooler Adapter Hose Kit This kit is to adapt your factory 4R100 transmission cooler lines to a 6.0L Ford Powerstroke transmission cooler that has the 1/2 inch ports. INCLUDED IN THIS KIT: 6' x 1/2" Transmission Cooler hose...

94.5-97 7.3L CNC Fabrication E4OD Transmission Cooler Adapter Hose Kit This kit is to adapt your factory E4OD transmission cooler lines to a 6.0L Ford Powerstroke transmission cooler that has the 1/2 inch ports. INCLUDED IN THIS KIT: 6' x 1/2" Transmission Cooler hose...

This is typically an add-on product option for one of our 4-line feed fuel line kits.  94.5-03 7.3L CNC Fabrication Fuel Filter Relocation Kit - 422100 INSTALLATION INSTRUCTIONS 

Introducing the ultimate fuel upgrade for your 03-07 6.0L engine that is equipped with a Stock intake plenum. The CNC Fabrication 4-Line feed stainless steel fuel line kit! Designed with precision and durability in mind, this kit will take your fuel system to the...