Upgrade your 94.5-95 7.3L Ford Powerstroke with these billet intake plenums from CNC Fabrication.  These are a nice upgrade over the stock flimsy stamped sheet metal and will not deform the center inlet port when installing your CAC boot clamps. Features: 8 Bolt design...

Product Description: Engine Oil Temperature (EOT) Sensor OEM Numbers: F5AZ12A648AB, 3F1Z12A648A, DY961, DY1144   Make Model Years Engine Model Notes Notes Ford F-250 1994 to 2003 Ford 7.3L Power Stroke   F Series, Excursion, E Series Ford F-350 1994 to 2003 Ford 7.3L Power Stroke   F Series, Excursion, E Series...

Product Description: Valve Cover Harness Connector Repair Kit   Make Model Years Engine Model Notes Notes Ford F-250 1994 to 1997 Ford 7.3L Power Stroke   F Series, E Series Ford F-350 1994 to 1997 Ford 7.3L Power Stroke   F Series, E Series Ford F-450 1994 to 1997 Ford...

This is a great addition when using the high flow outlet or a “gutted” stock outlet. This direct bolt-in replacement for the factory pedestal will eliminate leaks from the EBV actuator assembly and works with the factory turbo, Garrett TP38r ball bearing turbo, and Turbonetics ball bearing “drop in” turbos....

NEW Genuine Ford OEM Exhaust Back Pressure Tube for 94.5- early 97 FORD 7.3L Powerstroke Diesel Engines **For sensors mounted to the HPOP reservoir, not the front cover.  

The SES light for overboost will come on at about 25 lbs. causing the PCM to decrease fuel delivery attempting to control the boost.  This condition usually occurs in "chipped" vehicles. Our BRV+ (Boost Relief Valve Plus) will relieve any excess pressure to the map sensor while...

94.5-03 7.3L Powerstroke (Vin code F) lower gasket set- CS54204A CONTAINS THE FOLLOWING: Oil Pan RTV Rear Main Seal Water Pump Gasket Water Outlet Gasket Oil Pickup Tube Gasket Rubber Rear Main Seal Timing Cover Gaskets/Seal Oil cooler seals HPOP reservoir seals

Upgrade your 94.5-95 7.3L Ford Powerstroke with these billet intake plenums from CNC Fabrication.  These are a nice upgrade over the stock flimsy stamped sheet metal and will not deform the center inlet port when installing your CAC boot clamps. Features: Larger 3 inch...

S&B Silicone Body Mounts replace the old, worn body mounts on your truck and are a direct fit. Built from a premium silicone construction, the S&B Body Mounts are built to last a lifetime and will help isolate the harsh road vibrations.   FEATURES:...

This kit is to install a 1/2" draw straw suction tube in the fuel tank to feed your AirDog fuel pump. This kit installs by drilling a hole in the top of the fuel tank and securing the bulkhead fitting with a grommet. The...

This line is a replacement passenger side line for the '94.5 through '97.  If you have e-fuel you can also use the SD passenger line for a cleaner install. Features: All new Genuine Brennan™ fittings  DuPont Teflon™ lining just like OEM Burst pressure rating of...

Replacement fitting pack for CNC Fabrication's HPOP HPX line All new Brennan™ Hydraulic fittings  High quality Viton™ o-rings DOWNLOADABLE INSTALL INSTRUCTIONS INSTALLATION:   Disconnect the battery grounds before installation to avoid accidentally arc'ing the line on the glow plug relay or the alternator charging lug....

94.5-03 7.3L Alliant Power Water Pump - AP63501 Product Description: Water Pump Includes mounting gasket OEM Numbers: F81Z8501ARM, F81Z8501CRM, F6TZ8501AARM, 2C3Z8V501BA Make Model Years Engine Model Notes Notes Ford F-250 1996 to 2003 Ford 7.3L Power Stroke   F Series, Excursion, E Series Ford F-250 1994 to 2005...

For optimal air filter performance, it is essential to clean and oil your S&B Filter regularly. The S&B Filters 88-0009 Precision II Air Filter Cleaning & Oil Kit (Blue) includes everything you need to keep your filter running like new. The blue filter oil...

94.5-97 7.3L CNC Fab HPO Lines w/ Crossover Fitting Pack All new Brennan™ Hydraulic fittings  High quality Viton™ o-rings DOWNLOADABLE INSTALL INSTRUCTIONS INSTALLATION:   Disconnect the battery grounds before installation to avoid accidentally arc'ing the line on the glow plug relay or the alternator charging lug....

This non-exhaust back pressure valve turbo pedestal eliminates a few problematic oil leaks due to the factory pedestal actuator arm seals that often wear out. Eliminates the back plate seal and actuator arm seal Adding the NON-EBPV (aka High Flow Outlet) lowers EGT's More...

NEW Genuine Ford OEM Exhaust Back Pressure Tube for 97.5-98 FORD 7.3L Powerstroke Diesel Engines   THESE HAVE BEEN DISCONTINUED BY FORD

Product Description: 2 Wire Pigtail   Fits AP63416, AP63417, AP63418 Injection Pressure Regulator(s) (IPR), VGT solenoid on 11-17 6.7L, and also 7.3L "A" code injectors.   Make Model Years Engine Model Notes Notes Ford 4.5L LCF 2006 to 2010 Ford 4.5L Power Stroke   4.5L LCF Ford F-250...

These CNC Fabrication, LLC remanufactured Super Street (250/100 or 250/200) hybrid injectors will put new life back into your 94.5-03 7.3L Ford Powerstroke. Commonly called a Stage 3, these "Super Street" 250cc hybrid injectors will typically produce around 550-600hp with proper supporting modifications depending...