This kit is to install a 1/2" draw straw suction tube in the fuel tank to feed your AirDog fuel pump. This kit installs by drilling a hole in the top of the fuel tank and securing the bulk-head fitting with a grommet.

The Kit Includes:

• 1 1/2" Draw Straw Suction Tube Assembly
• 1 7ft 1/2" Fuel Line
• 1 Draw Straw Grommet
• 2 FQC12 Female 1/2" Quick Connect to Male 1/2" Push to Lock Fitting
• 1 08J2044-3/4UNF Male 3/4-16 O-ring Boss to 1/2" Male Quick Connect Fitting
• 1 08J2044-916UNF Male 9/16-18 UNF O-ring Boss to 1/2" Male Quick Connect Fitting
• 1 08J2044-3/8NPTF Male 3/8 NPT to Male 1/2" Quick Connect Fitting

For model years 1999-2007.

Tank comes complete with powder-coated or plated steel mounting strap set, extruded rubber mounting bushings, vent hoses, rollover safety vent valve, high-strength mounting bolt set, seals and required clamps.

Tank features exclusive low fuel trap design. For Crew Cab or Extended Cab equipped vehicles with 8.0 ft. Long Beds. Tank hangs approximately only 1.5" below bottom of the stock fuel tank shield bracket (on vehicles so equipped), and is approximately 2.5” deeper than the stock OEM tank.

For F250 HD, F350 HD, and F450 HD Models with Power Stroke Engines.

Not for Cab & Chassis model framed trucks

Please Note: There is no shield for this tank

For model years 1999-2007.

Tank comes complete with powder-coated or plated steel mounting strap set, extruded rubber mounting bushings, vent hoses, rollover safety vent valve, high-strength mounting bolt set, seals and required clamps.

Tank features exclusive low fuel trap design. For Crew Cab equipped vehicles with 6.5ft (short) beds. Tank hangs approximately only 1.5" below bottom of the stock fuel tank shield bracket (on vehicles so equipped), and is approximately 2.5” deeper than the stock OEM tank.

For F250 HD, F350 HD Models with Power Stroke Engines.

Not for Cab & Chassis model framed trucks

For model years 1999-2007.

Tank comes complete with powder-coated or plated steel mounting strap set, extruded rubber mounting bushings, vent hoses, rollover safety vent valve, high-strength mounting bolt set, seals and required clamps.

Tank features exclusive low fuel trap design. For Crew Cab equipped vehicles with 8.0 ft. Long Beds. The tank also includes a heavy-gauge steel nose skid plate. This plate protects the transmission and transfer case of the vehicle as well as supports and secures the large tank in place. Tank hangs approximately only 1.5" below bottom of the stock fuel tank shield bracket (on vehicles so equipped). Tank is approximately 2.5” deeper than the stock OEM tank.

For F250 HD, F350 HD, and F450 HD Models with Power Stroke Engines.

Not for Cab & Chassis model framed trucks

Please Note: There is no shield for this tank

For model years 1999-2007.

Tank is constructed of military grade cross-linked polyethylene (XLHDPE). Compatible with most bio-diesel fuel.

Tank solves the problem of lining failure and corrosion in steel OEM tanks caused by fuel quality issues which can lead to extremely expensive fuel system repairs. Tank is light in weight, corrosion-proof, extremely durable and features a drain plug for easy maintenance. Complete with rollover vent valve, and stainless steel interior flanges.

Fits in the place of the OEM stock tank.  
In most cases this product replaces the following original FORD equipment part numbers: XC3Z9002AA, 6C3Z9002BA, 6C3Z9002A, 6C3Z9002E, 6C3Z9002F, 3C3Z9002AA, 5C3Z9002B

Note:

All 1999 vehicles originally came with a 37 gallon tank and will require an 8020099-191 model tank (see below), also straps and a skid plate from FORD. Model year 2000 vehicles may be either so it is best to call TITAN for proper model fitment.

Sending Unit is NOT included with tank.  

For model years 1999-2010 F-350, F-450, and F-550 Narrow Frame, Cab and Chassis vehicles.  

Diesel fueled vehicles only.

It has all the advantages of TITAN’s famous cross-linked polyethylene such as its invulnerability to corrosion, resistance to heat transfer and condensation, durability and maintenance of its good looks. It includes a pre-wired 12 volt transfer pump that does approximately 8 gallons per minute (basically equivalent to standard gas stations).

The motor is UL Listed to U.S. and Canadian safety standards and comes complete with power cord, and manual nozzle. This fully baffled tank comes with a "Free Spinning" locking cap, mechanical fuel gauge, and all mounting hardware is included. One of our large locking toolboxes (Purchased separately below 99 9115 0000 or 99 9116 0000) can fit on the tank to enclose the transfer pump as well as hold tools. The transfer tank fits most all full-sized diesel pickups regardless of bed length.

TITAN’s™ cross-linked polyethylene (XLHDPE) in-bed tanks give you the advantages of advanced design and materials, as well as TITAN’s legendary quality and durability.

FEATURES:

• Fully Baffled
• Fuel Gauge is Standard
• Only weighs 51 lbs for easy to Install or Remove
• .250” Nominal Wall Thickness
• No Condensation and corrosion proof
• “Free Spinning” Locking Cap 
• Zinc Plated Hardware 
• Features Tie-Downs for Your Payload
• No Welds to Crack
• Nearly 200 Times Less Heat and Cold Conductive than Metal Tanks
• Durable Finish
• Compatible with most bio-diesel fuel+.
• Fits most pickup beds
• 59.50” long at top, 48.50” at bottom x 18” wide x 21” high (model 5110060)
• Patent Pending
• Use as “auxiliary” or “transfer”
• Convenient built-in lifting handles tank
• Mounting template and detailed instructions
• Lifetime warranty included on tank body

At your command, this in-bed tank transfers up to 60 gallons of fuel on-the-go.++ The TITAN™ Solid State, Electronic Controller lets you know how much fuel remains in your tank at all times. With the touch of a button, the controller pumps a preset amount of fuel into your main tank or another touch stops it at any time.

The controller is very compact and can be easily installed anywhere in your cab. This fully baffled tank comes with a "Free Spinning" locking cap and all mounting hardware is included. At 19 ½" high, the tank will fit under most standard tonneau covers. This system fits most all full-sized diesel pickups regardless of bed length.

TITAN’s™ cross-linked polyethylene (XLHDPE) in-bed tanks give you the advantages of advanced design and materials, as well as TITAN’s legendary quality and durability.

FEATURES:

• Fully Baffled
• Fuel Gauge is Standard
• Only weighs 51 lbs for easy to Install or Remove
• .250” Nominal Wall Thickness
• No Condensation and corrosion proof
• “Free Spinning” Locking Cap 
• Zinc Plated Hardware 
• Features Tie-Downs for Your Payload
• No Welds to Crack
• Nearly 200 Times Less Heat and Cold Conductive than Metal Tanks
• Durable Finish
• Compatible with most bio-diesel fuel+.
• Fits most pickup beds
• 59.50” long at top, 48.50” at bottom x 18” wide x 21” high (model 5110060)
• Patent Pending
• Use as “auxiliary” or “transfer”
• Convenient built-in lifting handles tank
• Mounting template and detailed instructions
• Lifetime warranty included on tank body